Fast Dry Heat Sterilizer(vertical)
Description
Vacuum drying: Avoid disinfection of the package after disinfection.
Pulse exhaust: positive pressure dynamic pulse exhaust, completely eliminate cold air in the sterilization chamber to ensure steam saturation.
Working procedures: water injection, preheating, pulse vacuum, sterilization, drying, and dormancy are automatically completed.
Microcomputer control technology: The sterilizer uses microprocessor intelligent control, humanized interface, easy to operate, safe and reliable. The parameters and status during the operation are dynamically displayed on the digital screen. After the equipment is abnormally detected automatically and the alarm is sterilized, the system automatically prompts and is accompanied by a buzzer sound.
Locking device: Before the sterilization cycle is started, the interlock is unlocked after the door is closed, and the door can be repeatedly closed and opened. The sterilizer can only be started when the door is closed, and the door of the sterilizer should not be opened during operation. After the start of the cycle operation, if the fault and fault indication occur, the sterilization chamber is not completely released, and the interlocking device should be locked, sterilizer door should not be opened.
Pulsation mode: microcomputer control automatically selects pulsation times according to site conditions to ensure the coordination of temperature and pressure.
Vacuum mode: three times of pre vacuum to ensure faster temperature rise and more thorough sterilization.
Safety valve: when the pressure of sterilizer reaches 240kpa ± 5kpa, the safety valve will automatically open to relieve the pressure.
Over pressure protection procedure: when the pressure of sterilization chamber reaches 220 ± 5kpakpa, there is a prompt sound and automatic pressure relief.
Air leakage: when the sterilizer is tested in each stage, the pressure rise rate shall not be greater than 0.13kpa/min.
Sterilization chamber dynamic pressure: The pressure change during any 2 s interval during the sterilizer cycle should not exceed 1000 kPa/min.
Vacuum pump: It adopts water ring vacuum pump, which is simple and convenient, with high vacuum rate and long service life. It is guaranteed vacuum can reach -80kpa.
Pressure sensor: The built-in pressure sensor automatically detects the pressure inside the chamber to ensure accurate and effective pressure in the chamber.
Temperature sensor: The built-in temperature sensor automatically detects the temperature inside the chamber, ensuring that the chamber is kept within ±3°C of the operating temperature.
Sterilization mode: dressing packaging, rubber products, BD test, high pressure and other sterilization modes.
Automatic drying: strong vacuum drying, suitable for drying requirements of different items; residual humidity of the device <0.2%.
Sealing structure: The sealing ring is made of silicone, and the design life is 2 years (1200 times) without aging and deformation.
Caster: Yes
Alarm system: There is a high and low temperature alarm system.
Category: Class II medical devices.
Technological parameters
| Product form |
Vertical |
| Heating mode |
Electric heating |
| Power |
16.0kw |
| Power supply |
AC380V, 50Hz |
| Dimensions (length × width × height) |
1150x770x1520mm |
| Liner size (diameter × depth) |
420×700mm |
| Volume |
100L |
| Weight |
310kg |
| Temperature display |
LCD |
| Design pressure |
0.29mpa |
| Rated working pressure |
0.21Mpa |
| Design temperature |
150ºC |
| Working temperature |
121 ° C / 134 ° C |
| Sterilization chamber safety valve |
Open >= 0.25Mpa, close <= 0.24Mpa. |
| Pulsation amplitude |
Positive value 0.065Mpa ~ 0.09Mpa, negative value -0.06Mpa ~ -0.08Mpa. |
| Pressure controller setting |
Upper change over value is 0.35Mpa, and the lower change over value is 0.34mpa. |
| Evaporator water source |
Softened water or purified water, water temperature ≤ 45 ° C, water pressure 0 ~ 0.05 Mpa. |
| Vacuum pump water source |
Tap water (hardness should not be too high), water pressure 0.10Mpa ~ 0.20Mpa. |
| Air discharge |
>99% (pulsation times 3 times or more). |
If you are interested in this, please contact me: Nana Zhang
Shanghai Medigrade Industry Co.,Ltd
Waigaoqiao Free Trade Zone, Shanghai,China
Cell Phone: 0086-15800947006
Tel: 0086-21-58589972
Fax: 0086-21-68689726
medigrade.en.made-in-china.com
Audited Supplier 
){kind=link}